| Specifications |
CHUCK WORK
Chuck diameter - (main spindle) 8" (sub-spindle) 6"
Type hydraulic
Maximum speed 4000 RPM
WORK LENGTH
Distance between spindle faces 27.5"
MACHINING CAPACITY
Maximum turning diameter 8"
Maximum turning length 16.93"
MAIN SPINDLE
Draw-tube capacity 2.75"
Spindle through bore capacity 3.15"
Spindle speed range (infinitely variable) 4000
Variable speed steps Direct drive
Spindle motor (Fanuc 22S) 35 HP
Motor type S series Spindle nose A2-6
SUB-SPINDLE
Drawtube capacity 1.77"
Spindle through bore capacity 2.17"
Spindle speed range (infinitely variable) 5000
Spindle drive motor (variable speed) max. rating 10 HP
Spindle nose A2-5 Slide movement - (B-axis NC control -
(X-axis) hi-lo Hydraulic
Slide stroke - (B-axis) 16.53" -
(Z-axis 9.44"
UPPER TURRET
Number of tool stations (main spindle) 12
Turret indexing time 0.15 sec/pos.
Turret indexing type Fanuc servo-driven bi-directional Slide stroke:
Z-axis 15.0" X-axis 6.5"
LOWER TURRET
Number of tool stations (main spindle) 8
Turret indexing time 0.15 sec/pos.
Turret indexing type Fanuc servo-driven bi-directional Slide stroke:
Z-axis 9.4" X-axis 5.8"
REVOLVING TOOL ATTACHMENT UPPER/LOWER TURRET
Number of upper turret positions 12 max
Number of lower turret positions 8 max
Drive motor - maximum rating (upper and lower turrets)
AC HP 5 Speed range (infinitely variable) 4000
Machine capacity (upper and lower turrets)
Drilling 3/4"dia. -
End Mill 3/4" dia.
Tapping. 1/2" dia.
Revolving tool axis X,C, & Z
GENERAL INFORMATION
Voltage required 230 volt AC, 3-phase
Air Supply 80 psi @ 4 CFM Amperage Dra 120 Amp.
MACHINE DIMENSIONS
Width. 83.8" Height 86.7" Length 122.7"
Length with chip conveyor 161.7"
Machine weight with conveyor 14,700 lbs |
| Notes |
It has a barfeed interface but we never saw what if any barfeed was on this machine.
The standard interface as far as I know will work on any barfeed properly installed.
Quattroflex 710 SLL
Universal Turning/Milling Center
MODEL QUATTROFLEX 710 SLL - 7-AXIS TURNING CENTER W/ SUB-SPINDLE &(2) LIVE-TOOLING TURRETS
o 2-3/4" Bar Capacity
o 35 HORSEPOWER MAIN SPINDLE
o c-AXIS MAIN & SUB-SPINDLES
(1) Fanuc 18i-TT 32-bit Pentium microprocessor control
(1) 10.4" color LCD graphic monitor with full keyboard
(1) 4000 RPM main spindle speed
(1) 35 horsepower AC wide range spindle drive motor (230 volts)
(1) 5000 RPM sub-spindle speed
(1) 10 horsepower AC wide range sub-spindle drive motor (230 volts)
(1) 12 station upper turret (12-live tooling)
(1) 8 station lower turret (8-live tooling)
(1) Main and sub-spindle C-axis
(4) 5-horsepower revolving tools
(1) Rigid tapping on main, sub-, and live-tool spindles
(1) Double tool probe
(1) Eurotech tool monitoring system
(1) 710SLL tooling package including (4) revolving tools
(1) Coolant flush system
(1) Sub-spindle ejector and airblow |
